膩?zhàn)臃墼谶\(yùn)用的時分需要進行拋光的處理，在進行拋光的時分需要把握時刻，很多人并不是很了解。膩?zhàn)臃墼鯓影盐諕伖廪k法？接下來膩?zhàn)臃蹚S家就來為我們介紹有關于這方面的常識，一起跟著膩?zhàn)臃蹚S家來了解一下。

　　Putty powder needs to be polished during use, and it is important to grasp the timing when polishing, which many people are not very familiar with. How to grasp the polishing method of putty powder? Next, the putty powder manufacturer will introduce us to common knowledge in this area. Let's follow the putty powder manufacturer to learn more.

　　首要不是所有的膩?zhàn)佣伎梢話伖猓梢話伖獾哪佔右话阒阜麓赏苛匣蚰退佔樱┕r(shí)先批一遍膩?zhàn)诱职渍移剑涓珊笥蒙凹埓蚰ィ缓笈榇?成干時用批刀把外表壓平磨出光即可。

　　Firstly, not all putty can be polished. Putty that can be polished generally refers to porcelain like coatings or water-resistant putty. During construction, first apply a coat of putty to make it white and level. After it dries, use sandpaper to polish it, and then apply two coats. When it is 80% dry, use a trowel to flatten and polish the surface.

　　1、內墻膩?zhàn)用鎸訏伖鈺r(shí)要把握適宜的拋光時刻，拋光的Z佳時期便是待膩?zhàn)油獗硭∠Ш螅⒓催M(jìn)行拋光。

　　1. When polishing the putty surface layer of the interior wall, it is important to grasp the appropriate polishing time. The best time for polishing is immediately after the watermark on the surface of the putty disappears.

　　2、產品必定要在保質期內運用，膩?zhàn)臃蹚S家提醒如果超過保質期，有必要進行試刮，經檢驗合格后。在施工。

　　2. The product must be used within its shelf life. The putty powder manufacturer reminds that if it exceeds the shelf life, it is necessary to conduct a trial scraping and pass the inspection. During construction.

　　3、產品必定要注意防水，應存在在陰涼干燥處，而且保證包封無缺。

　　3. The product must pay attention to waterproofing, be stored in a cool and dry place, and ensure that the packaging is intact.

　　4、夏天或高溫氣候條件下，在施刮膩?zhàn)忧敖ㄗh先用清水潤濕墻面，墻面外表無明水后即可施刮膩?zhàn)印?/p>

　　4. In summer or hot weather conditions, it is recommended to wet the wall with clean water before applying putty. Once there is no visible water on the surface of the wall, putty can be applied.

　　膩?zhàn)臃蹚S家提醒墻面刮過膩?zhàn)痈闪诉^后出現發暗狀態,用拋光機拋光一次拋完再用紗紙紗一次,重復三次,再用拋光機拋光不必紗紙紗。有沒有拋光,新的拋光有必要用細紗紙500目的加水磨好,膩?zhàn)庸魏媒窈笤谄叨喟敫傻臅r(shí)分拋光一次,在9成干(從旁邊面看的時分有些墻面要干透有點發白)的時分再拋光一次,基本就光了,其實有一般只要進行拋光就會光,只不過要從旁邊面看才顯著,做的好的是又光又滑。

　　The putty powder manufacturer reminds that if the putty on the wall becomes dark after being scraped and dried, it should be polished once with a polishing machine and then with paper yarn. Repeat this process three times, and then use a polishing machine to polish without paper yarn. Is there any polishing? For new polishing, it is necessary to use fine yarn paper with 500 mesh and water to grind it well. After scraping the putty, polish it once when it is about 70% dry, and then polish it again when it is 90% dry (some walls may dry completely and turn a little white when viewed from the side). It is basically smooth. In fact, as long as polishing is done, it will be smooth, but it is only noticeable when viewed from the side. What is done well is smooth and shiny.

　　膩?zhàn)臃鄣姆峙浔容^簡略，膩?zhàn)臃塾斜匾钆湟后w才可以進行分配，現在有很多防水的膩?zhàn)臃壑恍枰们逅M(jìn)行分配，運用比較的簡略，還有一種膩?zhàn)臃鄣哪退圆皇呛芎茫敲淳鸵獏⒓幽z水進行分配，可是這種膠水不是很環保，所以膩?zhàn)臃蹚S家主張我們在購買膩?zhàn)臃鄣臅r(shí)分必定要挑選不需要增加膠水的膩?zhàn)臃邸Ｄ佔臃鄣臄噭右彩潜容^重要的，必定要把握好攪動的時刻和力度。膩?zhàn)映渑娴臄嚢韬媒窈螅o置15-20分的時刻，這個過程便是為了讓膩?zhàn)臃壑械脑黾觿┏渑娴娜芙狻?/p>

　　The distribution of putty powder is relatively simple. It is necessary to mix putty powder with liquid before distribution. Nowadays, many waterproof putty powders only need to be distributed with water, which is relatively simple to use. There is also a type of putty powder that has poor water resistance and needs to be distributed with glue. However, this glue is not very environmentally friendly. Therefore, putty powder manufacturers advocate that when purchasing putty powder, we must choose putty powder that does not require additional glue. The stirring of putty powder is also quite important, and it is necessary to grasp the timing and intensity of stirring. After the putty is thoroughly mixed, it should be left to stand for 15-20 minutes to allow the additive in the putty powder to dissolve sufficiently.

　　膩?zhàn)臃凼墙ㄖb修材料的一種，首要成分是滑石粉和膠水。剛剛購置的毛坯房外表的一層白色--膩?zhàn)樱ǔＤ佔拥陌锥仍?0以上細度在330以上。膩?zhàn)邮怯脕韷γ嫘扪a(bǔ)找平的一種基材，為下一步裝修(刷油漆貼壁紙)打下杰出的根底。膩?zhàn)臃譃閮?nèi)墻和外墻兩種，外墻膩?zhàn)右挚癸L(fēng)吹日曬所以膠性大、強度高，環保指數稍低。內墻膩?zhàn)泳C合指數較好，健康環保，所以內墻不外用，外墻不內用。

　　Putty powder is a type of building decoration material, primarily composed of talcum powder and adhesive. The white putty on the exterior of the newly purchased rough house usually has a whiteness of 90 or above and a fineness of 330 or above. Putty is a substrate used for wall repair and leveling, laying an outstanding foundation for the next step of decoration (painting, pasting wallpaper). Putty is divided into two types: interior wall putty and exterior wall putty. Exterior wall putty needs to resist wind and sun exposure, so it has high adhesiveness, high strength, and slightly lower environmental protection index. The comprehensive index of putty for interior walls is good, which is healthy and environmentally friendly, so it is not used externally for interior walls and not used internally for exterior walls.

　　膩?zhàn)臃蹚S家提醒通常膩?zhàn)邮鞘嗷蛟S水泥基的，這樣外表粗糙比較容易粘接結實。可是在施工的時分仍是要在底層上涂刷一層界面劑來封固底層一起進步墻面的附著力，讓膩?zhàn)涌梢愿玫恼辰Y(jié)在基面上。

　　Putty powder manufacturers remind that putty is usually made of gypsum or cement-based materials, which can make the surface rough and easier to bond firmly. But during construction, it is still necessary to apply a layer of interface agent on the bottom layer to seal it and improve the adhesion of the wall, so that the putty can better bond to the base surface.

　　本文來自：膩?zhàn)臃?/a>更多精彩內容請點擊我們的網站：http://www.daquanq.com.cn我們將傾情為您解答。

　　This article is from: Putty Powder. For more exciting content, please click on our website: http://www.daquanq.com.cn We will wholeheartedly provide you with answers.